I posted this on the surfermag site as well: try the Hynson Quads, Rusty Quads, or Mayhem quads. You want more surface area on a wide tail board and if you want drive, you want rake. Rusty Quads would be a good start.
Results 11 to 19 of 19
Thread: fin question
Apr 13, 2011, 04:25 PM #11Member
- Join Date
- Feb 2010
Apr 13, 2011, 04:40 PM #12
- Join Date
- Jan 2009
- milton delaware
First one was a 6'0" with the fins a bit further back and much further off the rail, closer to the stringer with less toe. To me the board felt sluggish and no drive out of turns. I thought i didnt like quads....but eventually gave quads another shot.
The second two quads the rear fins were out on the rail just behind the front fins, and with almost equal toe in. the boards feel faster down the line and spring forward out of turns.
Apr 13, 2011, 05:09 PM #13Member
- Join Date
- Sep 2010
- Chesapeake Va
I have 3 fish shapes (All quads) and a different fin set up for each one because they all perform completely different. I did the try it before you buy it route with fcs at a local shop and slowly got each board dialed in.
Apr 13, 2011, 05:15 PM #14Senior Member
I totally agree at least try the quad set that comes with the board. I personally when going quad fins prefer a flat inside foil. I have the Slater (5 fin set) but that quad set up is great, but if your bigger the board is a really wide tail you probably need a bigger fin. I would try the MR quead set up for a fish type board, Basically a big ol set of twin fins with some smaller stailzers in the back, should be really fun in a fishcuit syle board, having that much fin in the water with a flat inside foil you should get some drive out of them. If you work at a shop you should be able to "test drive" plenty of fcs fins right?
- Join Date
- Jun 2010
In tiny surf I've taken the trailers out and ridden as a twin. Went well, but a little less drive it seemed.
I got the set of gx trailers double foiled so I can use one as trailer in a twin plus trailer setup, but I have yet to try that. I keep meaning to, but then when it comes time, I just end up leaving the quad set in there cus I know it works for me.
I really don't know much about fins. I tried this setup after reading some reviews for Todd Proctor's little Rascal 2, which is somewhat similar to the shape of my board. He puts this setup on his stock...I copied. Mine are glass flex, so their not as stiff as they should be, but I cheaped out. The fronts are the MRTFX.
I had someone that knows alot more than me about fins suggest the Rusty set previously mentioned as well. Supposedly they have a lot of drive for bigger guys.
Apr 13, 2011, 05:30 PM #15
True, everyone has a personal preference. Here's what I've figured out for myself, and it might make sense to you...
The general rule for me is, the closer the rear and front fins are on a quad... a true quad, not a twinzer, etc.... the closer the fins should be in size, shape, and foil. As the cluster spreads out, the need for the fins to act independently increases, and the more the fins need to be a different size, shape and foil. If the toe is about the same, and the fins are only an 1 - 1 3/8 apart (leading edge to trailing edge), regular side fins from a thruster set work best. You can have some difference in area, but not much... bigger fins in front if you do. These two fins "work together." The exception to the rule is the speed dialer type fins, which I am not a big fan of. They're supposed to work like a split keel, but for me, a regular well placed, single foiled, slightly toed and canted keel works a lot better.
As the fins cluster spreads out... rear fins back further, and closer to the stringer... the toe and cant angles should change, the size of the fins should change (larger fins in front, in most cases), and the foils of the front and rear fins should change... in extreme cases, you can use double foiled fins as rear fins, if their toe and cant is nearly straight. This is to accommodate the different arc the rear fins trace out during a turn than the front fins... the front fins have a bigger radius than the rears, so they have to travel through the water at different angles to minimize drag.
Apr 13, 2011, 09:27 PM #16
this thread has given me a LOT to think about, fin-wise. i'll have to take a second look at the mayhem, rusty, & slater sets when i work next.
Apr 14, 2011, 01:31 PM #17
Apr 14, 2011, 07:18 PM #18
Apr 15, 2011, 09:40 PM #19
At 200 lbs the stock m-5 fronts and qx rears didn't work for me either. My thruster set up is TC redlines. Long story short I smashed my center fin on a coral head and got out of the water to replace it but only had my stock set in the vehicle. TCs up front & Qx in the back. I'm am so stoked on it I have yet to change it back even though I have another set of TCs and 2 sets of MRs. Speaking of which does anyone else hate the trailer on the MR sets? I thought it was a regular GL and tried to surf it as such and was embarrassed.