Well, I got bored last weekend and realized I haven't made anything in the shop recently--my last project was almost every evening and almost every weekend for over 4 months building a custom queen sized bed with incorporated foot trunk, two shadow box end tables and a shadow box coffee table. (a paying project) So, after a month long hiatus I was getting the itch to build something new.
I didn't want to get too involved with something I would have had to commit serious amounts of time to, but I knew I wanted to experiment with something I've never done--building some sort of water craft. I figured I should start small, so I decided to mess around with some hand boards. I started going through my racks of scraps and cut-offs and pulled out some OG Heart Pine, Black Walnut, Quilted Maple and Wenge. I commenced with re-sawing, dimensioning, planing and joining and wound up with some stock I could make a couple blanks from. While they were glued up I sketched out a fat fish-like template on cardboard and cut it out with an exacto knife when I was satisfied with the lines.
(I will go ahead and apologize in advance for the crappy pics taken from a dusty cell phone)
On to drawing out the template and cutting the rough shape:
Results 1 to 10 of 76
Thread: Experimenting With Hand Boards
Jul 17, 2013, 01:09 PM #1
Experimenting With Hand Boards
Jul 17, 2013, 01:19 PM #2
One one plane I went with a classic offset stripe using the OG Pine for the majority, a smaller strip of Black Walnut and finished off with some Quilted Maple. The other one is dominantly Quilted Maple with a Wenge "stringer."
I'm trying to incorporate as many variables as I can to see if any make a difference in performance, so I decided to do the Pine one as a deep stepped single concave with two incorporated skegs at the tail and the Maple one with a single vee throughout most of the board and deep double concave. Since I'm experimenting I just drew reference lines on the boards, broke out a router, stuck a 1 1/2" fluting bit in it and went to town:
Jul 17, 2013, 01:38 PM #3
Now that I had the boards fully roughed out it was time to get down to what represents over 50% of carpentry... sanding.
This is where I realized I should have been a little more careful in routing the concaves when stepping the bit down. My lines turned out fairly straight and uniform, but leaving those harsh transitions doubled my sanding time.
I sanded my rail profiles on the bottoms then flipped the boards over, threw a 1/2" round-over bit on the router and did the same on the top, fairing out the noses and slightly rounding the tails with more considerable sanding. Then I filled some knot voids with epoxy and that's pretty much how they sit right now.
I'm leaning towards finishing them with Helmsman spar urethane but will probably start using epoxy in the future.
I still haven't figured out what I am going to use for the hand straps and exactly how I'm going to attach them to the boards. I'll probably go a quick and dirty route on these then upgrade on the next ones I make.
That's it for now, I hope to get some more done on them over the next few days. I hope y'all enjoy!
Jul 17, 2013, 01:40 PM #4
Hell, at some point I'll even measure them and post the dimensions.... I have no idea what they are.
Jul 17, 2013, 01:47 PM #5
Nice work, Erock.
Do you make coffee tables?
Jul 17, 2013, 01:59 PM #6
That is some solid work. I got one at a local shop on sale and its a ton of fun. You can't help but 'plane out' once you get your weight behind it. Lets see some footage of you getting a 1 foot tube!
Jul 17, 2013, 02:00 PM #7Member
- Join Date
- Jan 2009
- in the tits
looks good how long did this take you?
Jul 17, 2013, 02:49 PM #8
Nice work. I want one.
Great minds think alike I guess. I had some extra sapelle scraps laying around and made these two. More work to come. Got some keels foiled out too.
I like the detail on the one with the lighter wood on the right side. Looking good.IMG_3867.jpg
Jul 17, 2013, 03:12 PM #10
- Join Date
- Dec 2007
Did you use a router to put the channels in?