Results 51 to 60 of 77
Thread: Experimenting With Hand Boards
Jul 19, 2013, 11:39 PM #51
Jul 20, 2013, 04:38 AM #52Member
- Join Date
- Jun 2013
took the fat model out in the water today for the first time. It was a blast shouldve taken some pics maybe next time. Cant tell you the last time I went home with so much sand in every orifice of my body and shorts though.... Ahh the beach break.
Aug 1, 2013, 10:33 PM #53
Alright! I finally got a chance to give them a spin for about an hour today in 2.5' @ 10 second low tide waves from 11a-12p right on the South side of Crystal--it was surprisingly lined up pretty nice but a little fat then pitching on the inside.
I don't have any swim fins at the moment and there was no way I was going to use my 4' long spearing fins without my pink tutu and glow sticks, so I stole my wife's fins..... They're big on her and she wears neoprene socks with them, so I thought I would be ok although tight.... Well.... Let's just say I've got 5 blisters on the tops of my toes that I just ripped off and applied liquid bandage (been a long-time user, best first aid item ever) on top of them. Not sure I have ever felt pain quite so acute--liquid bandage always stings but this was insane. Anyway, back to the ride report...
I caught about 15 or so waves with each board to see if I could tell a difference in the different bottom designs. The one with the Wenge stringer and the vee through the middle tracked a little more straight than the other with deep single concave and keels--but that was about all I could tell in this preliminary session. Both boards gave me a good bit of speed down the line as they should, I out ran a couple of the mushier waves.
They both really turned on in the steeper, barreling waves. It was like stepping on the gas as soon as I got in the pocket, I was able to keep up with the barrel until it finally closed out. Again, it didn't matter which board I was using, so I'm sure it's just the effect of using a hand board (which I'd never done before).
One thing I'm going to do on the next couple I make is to considerably foil the rails. These two have really full rails and I want to see how much a change in that variable affects the performance.
Here's a pic of them after their maiden voyages:
The straps are quick and dirty. I went to a hardware store and got the following: nylon fairleads, 3/8" stainless screws, 4' 1/2" poly strapping and 1/2" strapping buckles. Once I got home I got really safe and pulled out my wife's sewing machine--but it couldn't handle the thickness, so I had to do it by hand. I suck at sewing by hand, so we'll see how long my handiwork lasts. I have yet to cut up an old wetsuit to sew together some sleeves to go over the strapping to make it a little more comfy (even though they are by no means uncomfortable how they are). In any case it should be a nice aesthetic touch. But, at least they are adjustable so my friends with monkey hands and those with "soft hands" can give 'em a go.
Next time I'm also going to figure out how to put some leash plugs in them--I have to experiment with how much depth I can take out of them without affecting their strength.
Aug 2, 2013, 04:50 AM #54Member
- Join Date
- Jun 2013
nice planes erock!
Aug 17, 2013, 11:12 PM #55
Aug 17, 2013, 11:28 PM #56
Aaaaaaaand speaking of my newest experiments:
I've got a couple irreparable poly boards hanging around and I've been trying to make some space in my shed, so I got a bright idea this rainy-assed morning. I pulled out this old mini longboard (about 8') my dad found god-knows-where a couple years ago and took it over to the shop with the intent or ripping all the glass off. I grabbed the Dremel, threw on a cutting wheel and sliced a line all the way around the rail line (I'm gong to once again pre-apologize for the poor picture quality and not taking enough photos--I got in a safety-induced zone):
I think you can see the cut and the crap-tastic wax job on the board
Then I ripped all the glass off. The deck came off in almost one piece but the bottom was a b!tch.
After I stripped the glass, I took a pull saw and ran it down both sides of the stringer then cut each side of the blank down into pieces (no pics ..)
I took one side of the nose, pulled out my original fish template then put some scaling marks on it, messed around and eventually came out with a smaller pin tailed blank:
I broke out a Sure Form and some 120p sanding screen and set about cutting a serious single concave that runs from the nose then turns into a double barrel vee kind of thing through the tail. I put some really knifed upper foils on it:
Aug 17, 2013, 11:37 PM #57
This one has almost zero rocker.
I then figured I could bust another design out while I was feeling inspired, so I took my fish template and traced it onto another block. Instead of doing the fish tail I wanted to do a half-moon so I pulled out a 5 gallon bucket lid, got it lined up and traced it. Then on to cutting the outline:
I wanted to try something different again, so I decided to put some nose rocker into this one. After some reference lines and fervent stroking of the Sure Form:
Aug 17, 2013, 11:41 PM #58
Since I was "doing something different," I decided to put a forward vee on the nose that carries to the rocker's entry point then dug out a large concave in the middle with slightly smaller ones going to the rails.
Again, I put some serious knifing into the rail foils:
I'm not sure when I'm going to end up glassing these, but I think I'm going to try and shape a couple more designs while I'm at it then glass them all at the same time. I'm thinking I should try some of that bedazzled artsy fartsy chitt and do some experimenting with cloth underlays, resin tints and the like. We'll see.
I'll post up the other shapes as I make them. It's time for dinner now.
Aug 17, 2013, 11:44 PM #59
I'll try and remember to have a real camera on me next time. Those pics SUCK!
Dec 5, 2013, 03:08 PM #60
Well, I shaped out another wooden one... this one is going to be auctioned off on Friday (12-6) at the Hope From Helen Benefit... Blockade Runner, WB 6:30-9:30 for those in the area interested in attending.
I used my same old fish template but widened it out by about 1/2" at the widest point as well as lengthening by around 1". I was aiming to make something with more planing surface to use in more mushy waves. I also added a concave deck, more overall concave on the bottom with more flowing transitions, an 80/20 knifed rail at the front entry going to a harder square rail pretty quickly at the mid point and holding through the tail. I also gave it more rocker in the nose. Too bad I will probably never get a chance to see how this one works....
Hand Board Porn:
First a couple comparing to my original design: