Page 46 of 127 FirstFirst ... 3644454647485696 ... LastLast
Results 451 to 460 of 1265
  1. #451
    Roy the only boards with foil errors are yours. Also ive been getting messages since that space balls darth vader picture was posted about how full of Shiiiiit you are and how anyone in discussion with you is wasting ones time.

  2. #452
    Did you read the info regarding the fin noise?

    It's most likely a trailing edge foiling error ( very common) or a damaged trailing edge.

  3. #453
    Roy did you read my reply? The only board with foil damage or error are your boards.

  4. #454
    As stated the noise you are experiencing is very common, it is due to a fin trailing edge anomaly and it happens at certain speeds and angles of attack where the non beneficial vortex frequency enters the audible range.

    It's a well known well researched phenomenon which is easily cured. Check out the trailing edges of your fins or fin. If there's no damage it is a foiling error. Many fins have a foil section which includes an accelerating curve or 'hook' and sometimes these cause the issue.


  5. #455
    Roy you are not qualified to make a diagnosis. Btw who said the noise is caused by an error or a damaged foil? I just don't know where to take far as explaining how ridiculous you are. I have heard this effect on every board that has a camera mounted to capture the sound. So let me ask you, when a jet travels at a high speed and a screaming noise is created - not from the engine, do the wings need to be fixed or is it a phenomenon?
    And before you go on embarrassing yourself, I work in industrial prototyping and I'm versed in these areas.

  6. #456

  7. #457
    Roy you need to do two things. I've suggested this to you before but here it is again:
    1. You need to take a business class
    2. You need to take a class on design or an entry level physics class.

  8. #458
    Quote Originally Posted by MFitz73 View Post
    Roy you need to do two things. I've suggested this to you before but here it is again:
    1. You need to take a business class
    2. You need to take a class on design or an entry level physics class.
    You are still in denial over the fin hum/fin issue, the surfboard lift issue and the elementary physics of surfing, just for a start.

    Instead of making vague superior sounding noises you should concentrate on physics yourself as you have shown a lack of understanding on all the issues raised so far.

    Let's take the surfboard noise issue. You still illogically maintain that I am incorrect in diagnosing probable fin trailing edge issues .... I suggest that you take some sandpaper and correct the trailing edge, it will probably cure the problem.

  9. #459
    No Roy this goes back to your mis understanding (I'm being kind to you) of the thruster set up. What I'd like you to do is get yourself a thin stick of decent length. Now swing it through the air at a good speed. I want you to think about why noise was created. You've demonstrated deep misunderstanding of the simple concepts. I'm here to help you. Who knows maybe even help you make a better board.

  10. #460
    Join Date
    Aug 2009
    Monmouth Beach, NJ
    Quote Originally Posted by Roy Stuart View Post
    The amount of lift produced by a foil depends upon at least 5 factors, and it is thus meaningless and hardly a 'play on words' to state that the lift of a double foiled fin ( which is what you are using as your argument against lift being produced by single fins) is 'nothing compared to single foiled fins'.

    Single fins are quite capable of producing more lift than other fin setups, it depends upon many factors: area, foil, aspect ratio, speed, angle of attack, chord ratio etc.

    So the bottom line is that I am correct and those who have stated here that single fins cannot create lift at all are wrong... there's some careful back pedalling rearguard action going on, but 100% wrong is still 100% wrong.
    Roy... you are so caught up in being right, and everyone else being "incorrect," that you can't have a comprehensive discussion about design. Loosen up... just a little. Not everyone here is against you. You know the difference between the lift force created by symmetrically foiled and asymmetrically foiled fins... and how those forces change and compare at varying angles of attack. Why can't you just talk about that? Why confound a very simple principle with at least four more factors, with no context or explanation?

    I'm an educator. Here's what we call a "teachable moment." Talk about what you know so others understand. Unless, of course, you don't WANT others to understand. Then just focus on the argument, and not the content of the discussion.